i am using 48 MHz crystal. usb tested in bootmod, there also problem, Pls find below logs :- DCU > usb start (Re)start USB... USB0: check_usb_device_connecting timeout. scanning bus 0 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found hpl-dcu> usb info 1: Hub, USB Revision 1.10 - U-Boot Root Hub - Class: Hub - PacketSize: 8 Configurations: 1 - Vendor: 0x0000 Product 0x0000 Version 0.0 Configuration: 1 - Interfaces: 1 Self Powered 0mA Interface: 0 - Alternate Setting 0, Endpoints: 1 - Class Hub - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms DCU> usb storage No storage devices, perhaps not 'usb start'ed..? Pls help.

Yes Scott, according to document its not possible I think. Please see the point 5 of section 2.5 in the document link given below. It is written that "The user extension area cannot be rewritten by the FCL". So I think its not possible to write user extension area from FCL. Please go on the below Link for the document : www.renesas.com/.../r01us0069ej0102_rh850.pdf If there is any method to write user extension area then please let me know. I am not clear how can I write this area?

Jimmie, Have you found the answer you were looking for? Mike Clements RenesasRulz Moderator

ab, Have you found a solution to your issue? Mike Clements RenesasRulz Moderator

Bill, Have you found your answer? Mike Clements RenesasRulz moderator

Mad River, Have you resolved your file extension issues? Mike Clements RenesasRulz Moderator

Martin, Is your project working? Mike Clements RenesasRulz Moderator

KR, Is your e2studio working now? Mike Clements RenesasRulz Moderator

Jagadesh, Have you resolved your isse? Mike Clements RenesasRulz Moderator

RB, Have you tried importing your files using File>import? Mike Clements RenesasRulz Moderator

Djay, Have you resolved your issue? Mike Clements RenesasRulz Moderator

RakeshTata, Have you resolved your issue? Mike Clements RenesasRulz Moderator

MOSN, Have you resolved your issue? Mike Clements RenesasRulz Moderator

dybamictoys, Have you resolved your issue? Mike Clements RenesasRulz Moderator

Paul, Have you found the answer you were looking for? Mike Clements RenesasRulz Moderator

Gireesh, Have you resolved your issue? Mike Clements RenesasRulz Moderator

KarthiKeyan, Is your project working now? Mike Clements RenesasRulz Moderator

Mariya K, Is your image displaying properly now? Mike Clements RenesasRulz Moderator

swoo.quek, Was your question answered? Mike Clements RenesasRulz Moderator

It hasn't worked with the PDG because he has made problems with the includes. I've now adjusted the following example for my purpose and made a build but how can I show a variable over the E1 Debugger in the console? renesasrulz.com/.../rx62t-spi-port-usage

Forum Post: RE: RZ-A1H USB HMSC Issue

Forum Post: RE: RH850F1L Flash memory

Forum Post: RE: RZ/T1: Changing the priority of the current interrupt

Forum Post: RE: AVCC0-1 Ranges related to VCC (RX64M)

Forum Post: RE: BSP vs File Import

Forum Post: RE: FX Directory navegation

Forum Post: RE: add UART on Blinky project

Forum Post: RE: Correct way of installing e2studio for RZ microcontrollers

Forum Post: RE: Power on reset for H8s2128

Forum Post: RE: Simple RL78/G1D project Setup

Comment on issue regarding configuration of mbr3116 through r8c25276 i2c

Forum Post: RE: Simple program execution - RL78/G1D reference board

Forum Post: RE: R-Car H2 Surround View Application not working.

Forum Post: RE: S7G2 I2C example

Forum Post: RE: E1/E2/E2 Lite

Forum Post: RE: regarding ORCAD software

Forum Post: RE: WDT resting micro-controller

Forum Post: RE: Custom UI on S3A7 LCD

Forum Post: RE: Beginner for e2studio, Renesas MCU

Forum Post: RE: RX62T to RL78G13 SPI Communication