Forum Post: RE: Release Date, SSP 1.1.0?
Network outage has the site offline for now. I will post here when it is back online.
View ArticleForum Post: RE: How to add RGA library to existing e2studio project?
What is the folders that you can not find? If this is the common folder, try to copy from an_r01an2162ej0200_rza1h_other\workspace\RZ_A1H_RGA_Sample\RGA_Sample\armcc\common folder. I could find the...
View ArticleForum Post: RE: Parallel Communication for TFT
There is a lot of software involved in the Direct Drive TFT interface. I'm not sure what you mean when you say that the code runs on SPI of RX62N. It might be a good idea to start with the code for...
View ArticleForum Post: RE: RL78/G13 FDL Problem in Fast Execution
Hey Mahender Thanks For Your Support and Very Worth-full Helping Hand. There is No issue in Code there was one break-point which is causing things Tricky and ya i have Renesas E1 emulator through...
View ArticleForum Post: CRC calculation for different sections without modifying...
Hi everyone, Please guide me to calculate CRC for each sections (such as text, ro data etc) without modifying linker (.gsi) file. before, i use to modify linker file to fetch size and start address of...
View ArticleForum Post: RE: data sent from Linker file (.gsi)
thanks Paul and kaushik for your suggestions. am able to send integer through linker file as per your suggestions.
View ArticleForum Post: RE: DK-S7G2 Bluetooth LE module reset
Hi Josh, Thank you for your help! I have changed the Clock Phase setting of my SPI on SCI driver to Data sampling on even edge, data variation on odd edge and it worked! I now receive the correct...
View ArticleForum Post: DMA Link mode problem
Hi, I try to get DMA in link mode working, but when DMA is enabled, the DER bit of the Channel Status Register is set. According to the user manual, this bit is set when the LV (Link valid) bit of the...
View ArticleForum Post: Retarget virtual debug console to a file
Using e2Studio and the E1 programmer for RX111 series, I am able to get debug output in the virtual debug console. Is there a way to retarget the debug output to another stream, for long-term logging...
View ArticleForum Post: RE: DK-S7G2 Bluetooth LE module reset
Take a look at the datasheet again, in the one I found there is a jumper J1 on the module that would prevent a "reset" with the pin. It is not a real reset input, it does a complete Off/On cycle for...
View ArticleForum Post: RE: Pin compatibility for 5Volt of GR KAEDE Board.
This thread will be archived because of inactivity Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: nx_tcp_client_socket_connect failure
Hi, Try the User's manual: www.rtos.com/.../NetX_User_Guide.pdf Search for your API call nx_tcp_client_socket_connect. You will find the return value. hex(33) = 0x21 Implying: Invalid server IP...
View ArticleForum Post: RE: Startup code - e2studio
Hi Mirko, I would recommend reading the Synergy Software Package User's Manual SSP Overview BSP Architecture What Does the BSP Do? section to understand what the initialization is about. Peripheral...
View ArticleForum Post: RE: Handling analog fluctuations from sensors
This thread will be archived due to inactivity Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: Image processing library
This thread will be archived due to inactivity Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: Can we use Arduino IDE of GR-KURUMI and SAKURA to GR Kaede...
This thread will be archived due to inactivity Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: Sleep and Power Saving Mode function in GR Kaede
This thread will be archived due to inactivity Mike Clements RenesasRulz Moderator
View Article
