hi First of all, I regret my English. I am trying to put the IWDT in my application. I am using an R7FS3A17C3A01CFP and my configuration for the IWDT is: -IWDT is automatically activated after reset. -512 cycles (timeout period) -IWDT dedicated clock frequuency divisor 256 the micro should restart every ~ 9 seconds. (IWDT clock is 15KHz) In a blank project it works correctly, but in mine, it takes ~ 5 min 50 sec ¿Why? I have tried everything, but there is something that interferes with the IWDT account and I cannot find it.
↧
Forum Post: IWDT takes a long time
↧
Forum Post: rsu info write error 0xca5
Hi, when I tried to flash using the E1 debugger through GHS I am facing the rsu info write error 0xca5 previously I used the same board and debugger that time I am able to flash but suddenly Now This write error is coming. Please Reply me with some solution Thanks & Regards, G Sai Krishna.
↧
↧
Forum Post: RE: IWDT takes a long time
What is the setting for the OF0 regisrer, bit 14?
↧
Forum Post: Web Server Example Code - PK - S5D9
Hi, Hope everyone is having a great easter. Im currently struggling to get the code for a NetX/NetX Duo example projects working on the PK-S5D9. Below is a list of things ive tried. The code can be downloaded from here: https://www.renesas.com/us/en/products/synergy/hardware/kits/pk-s5d9.html#downloads - page two of the downloads list. Imported both projects into e2 and configured the IP to be a static IP (Checked the router and its not one that is currently used and is within the IP range of my router) and its not connecting. Now since everyone loves LEDs. Ethernet has two and only one of them is flashing (the orange one). – Just a note when I say ive imported them into the IDE. Its been independent of one another and when trying to run either of them the second one if present has been closed. Ive connected the device to the router and then checked the connections to the LAN network (Currently Lan3) and as you can see its registering speed but not the device. (also tried four). Ive also tried connecting directly to the pc again with the same IP as before and tried pinging it from the command line and tried connecting directly in chrome and neither have worked sadly. Ive tried replacing the static IP allocation with a DCHP client connection within the code and that hasn’t worked either sadly. Default gateway set to the IP of the router (as the PC). Stepped through the code to see if its erroring at all and all the threads are executing but seem to be waiting for something to happen (tx flags), The guide says a usb device is needed ive checked that and nothing is wrote on it so im not sure what that is required for. The only thing i havent checked as im struggling to get hold of the schematics (apologies if theyre infront of me and im looking in the wrong place) is the pin allocation for the ethernet channel. Ive seen previous forum posts saying that there is only a single channel on here and C0 is set to IOPORT_PORT_08_PIN_06 currently. (C1 is also allocated to the same pin). Ive checked through the code and nothing seems to be failing to Init as well. Im now at a bit of a loss as to what to try next or what the issue is. If you have any advice that would be greatly appreciated. Thanks, Chris
↧
Forum Post: Code coverage on ARM with E2Studio
I have a project on the S7G2 that I would like to get code coverage on. Is there a similar feature for to the "Renesas Coverage View" that supports ARM? Thanks, Matt Farley
↧
↧
Forum Post: RE: E2Studio and J-Link GDB Server remote debugging
Hello Joost, This Forum is for archiving, so I'm trying to prevent a new post to this Forum. I will move your post to the Forum "e2Studio", I ask you for accepting that. Rulz Admin RSV
↧
Forum Post: RE: File include error
Hi Kirti, Have you resolved this already? Maybe this thread can help you: http://renesasrulz.com/e2studio/f/e2studio-forum/10750/add-folder-to-includes JB RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ https://en-us.knowledgebase.renesas.com/
↧
Forum Post: RE: GHS Multi 850eserv2 Debug Server is aborted, while connecting to RH850-E1/L target
Hi Uma, How's this issue? Were you able to find a solution? JB RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ https://en-us.knowledgebase.renesas.com/
↧
Forum Post: RE: Unable to connect RH850 target using GHS Multi via E1 debugger
Hello Amine, Thanks for your support! I have tried this option still the same issues as mentioned above. Best Regards, Uma
↧
↧
Forum Post: RE: E1 Debugger work Area.
This thread will be archived due to inactivity. Herald RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ en-us.knowledgebase.renesas.com/
↧
Forum Post: RE: Design with the TPS-1
This thread will be archived due to inactivity. Herald RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ en-us.knowledgebase.renesas.com/
↧
Forum Post: RE: EEPROM Emulation Library
This thread will be archived due to inactivity. Herald RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ en-us.knowledgebase.renesas.com/
↧
Forum Post: Error(E100000E): A protection error occurred in the device
Hi , Iam using RH850 controller when I tried to Set the security option it got failed and then if I tried to flash it again but the tool is disconnecting and it is throwing error Error(E100000E): A protection error occurred in the device. (Response 12:DA) Operation failed. so I just wanted to know how to recover my controller from this state, any help is highly appreciated tool which I used is Renesas Flasher V3.x with E1 Emulator.
↧
↧
Forum Post: RH850 144 pin F1M: Taub0 Channel 9
The datasheet says channel 9 of TAUB0 unit is an independent channel with clock source as CK2. I want to use port10_15 as PWM output which is associated with CH9. My question is: 1.Can I use this CH9 as a slave channel for pwm output ? 2. With CH9 as a slave channel, can CH8 be used as a Master channel with CK3 for both slave & Master?
↧
Forum Post: RE: E2Studio and J-Link GDB Server remote debugging
Yes please, sorry I didn't notice.
↧
Forum Post: RE: SH7052: how to prevent FDT to erase memory while get connected?
Hi, I'm interested to your software but I can't find PM function
↧
Forum Post: RE: Problems when running GUIX project with custom build "GUIX Source"
Hi phil72, How's this issue? Were you able to make some progress? JB RenesasRulz Forum Moderator https://renesasrulz.com/ https://academy.renesas.com/ https://en-us.knowledgebase.renesas.com/
↧
↧
Forum Post: RE: E2Studio and J-Link GDB Server remote debugging
Which GBD server are you using? The e2studio one (e.g. C:\Renesas\e2_studio\DebugComp\Synergy\e2-server-gdb.exe) or the JLink one provided by Segger (e.g. C:\Program Files (x86)\SEGGER\JLink_V670c\JLinkGDBServer.exe)? You should be using the e2studio gdb server.
↧
Forum Post: RE: Web Server Example Code - PK - S5D9
The schematics are here :- https://www.renesas.com/en-eu/software/D6001035.html IOPORT_PORT_08_PIN_06 is correct for the PHY reset pin on the S5D9_PK board. Which version of the SSP are you using? The USB mass storage device is required to be inserted for the program to run, however, it does not actually hold any files for this particular demo setup (the web server can use the USB file system to store the web pages in a different setup)
↧
Forum Post: RE: E2Studio and J-Link GDB Server remote debugging
Thanks for the response. I didn't realize e2-server-gdb was the tool to use for this. Where can I find the arguments for e2-server-gdb to make it listen on a TCP port and connect to my target board? I have been guessing some based on gdbserver exambles, but no luck yet. I just noticed most arguments are right under my nose in the Renesas Hardware Debugging console, but these result in an error: PS C:\Renesas\Synergy\e2studio_v7.5.1_ssp_v1.7.5\DebugComp\Synergy> .\e2-server-gdb.exe -g SEGGERJLINKARM -t R7FS5D97E -uSelect=USB -uJLinkSetting=C:\Users\Joost\Canvas\P0144\hmi-board\P0144_HMI_debug.elf.jlink -uLowPower=0 -uInteface=SWD -uIfSpeed=4000 -uNoReset=1 -uResetPreRun=1 -uIdCodeBytes=FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF -uResetCon=1 -uSWOcoreClock=0 -uresetOnReload=1 -n0 -uFlashBp=0 -uSimulation=0 -uOSRestriction=0 -uCPUFrequency=0 -uCECycle=1 -l -uCore="SINGLE_CORE|enabled|1|main" -uSyncMode=async -uFirstGDB=main --english GDBServer for Renesas targets. Version 7.5.1.v20190813-134451 [2d1fc043] (Aug 13 2019 17:02:07) Starting server with the following options: Raw options : C:\Renesas\Synergy\e2studio_v7.5.1_ssp_v1.7.5\DebugComp\Synergy\e2-server-gdb.exe -g SEGGERJLINKARM -t R7FS5D97E -uSelect=USB -uJLinkSetting=C:\Users\Joost\Canvas\P0144\hmi-board\P0144_HMI_debug.elf.jlink -uLowPower=0 -uInteface=SWD -uIfSpeed=4000 -uNoReset=1 -uResetPreRun=1 -uIdCodeBytes=FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF -uResetCon=1 -uSWOcoreClock=0 -uresetOnReload=1 -n0 -uFlashBp=0 -uSimulation=0 -uOSRestriction=0 -uCPUFrequency=0 -uCECycle=1 -l -uCore=SINGLE_CORE|enabled|1|main -uSyncMode=async -uFirstGDB=main --english Connecting to R7FS5D97E, ARM Target GDBServer endian : little Target power : off Starting target connection GDB action 'connect to target', has failed with error code, 0xffffffff force_kill_gdb() Disconnected from the Target Debugger.
↧