Forum Post: RE: SH7780 goes to H-UDI
What do you mean by CPU goes to H-UDI? H-UDI has nothing to do with the CPU. The debugger unit can be controlled by H-UDI, and the debug unit can control the CPU. The CPU cannot access H-UDI. The...
View ArticleForum Post: RL78
Hi all, I'm wondering if multiple roles are supported? Acting as peripheral and central at the same time? Thank you.
View ArticleForum Post: RX Library Generator Abort
Hi, I have a problem with the library generator. I use the RX compiler toolchain v1.2.0 Basicly I do a buildprocess with the help of an own makefile, to compile my sources and link them. Also I use...
View ArticleForum Post: RE: HOCO as the main oscillator on the SK-S7 board
Hi Dale, Yes, that sounds like the way to go, thanks for the heads - up Alan..
View ArticleForum Post: RE: DK-S7G2 - QSPI Instruction Set
If you are in XIP mode, then no command is sent, only an address (3 byte address for default setup of QSPI on the S7-DK board). If you switch to Direct Communication mode, then commands are used to...
View ArticleComment on You Can Call Me Professor_IoT
Hello Gary (and Lou), We at Muco Technologies in the Netherlands are also looking forward to your comments and tips & tricks for the Synergy Platform. As an early bird we got the SK-S7G2 with...
View ArticleForum Post: RE: DMA on RZ/A1H
slu, Have you found a solution to your issue? Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: How to set TCRmn register with TDRmn register value after a stop
Grégory, Did you find a solution to your issue? Direct tech support is available: am.renesas.com/.../index.jsp Please let us know if you do find a solution. Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: RZ fail to execute MI command
jay123, Have you found a solution to your issue? Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: RZ/A1L RSCAN0RMNB NRXMB range
jkes, The numbers that can be counted with 5 bits, in binary, are 0-31. You are correct that there are 32 numbers available (0 being one of them). Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: Need information about BRK Exception in RX111
sanb, Have you found a solution to your issue? Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: RX 630 bootloader FFW Call error
Richard, This sounds like a question for tech support: am.renesas.com/.../index.jsp Please let us know if you find a solution. Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: CPU frequency error
Afreen, Have you tried submitting a tech support ticket? am.renesas.com/.../index.jsp Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: S7G2 to Segger Jlink hardware interface
Spoke to Segger and they said leave P11 RTCK unconnected. From Segger website "This pin is not used by J-Link. This pin is not used by J-Link when operating in SWD mode. If the device may also be...
View ArticleForum Post: RE: CPU frequency error
Afreen, The P1x series (and the Px4 before it) is particularly susceptible to user lockout due to invalid option bytes being programmed. (If I had to guess, I'd say that it's probably a mixture of...
View ArticleForum Post: RE: S7G2 to Segger Jlink hardware interface
Attached is spreadsheet showing connections per this blog discussion. Thanks Jeremy for your help.
View ArticleForum Post: RE: DK-S7G2 - QSPI Instruction Set
I'd like to add to this topic - I was able to set the SFMSDC.SFMXEN bit to 0. I found some funny behavior, however. After setting that register properly, I ran a loop of read commands and didn't see...
View ArticleForum Post: RE: e2studio debugging error
andrea, Did you find a solution to your issue? Mike Clements RenesasRulz Moderator
View ArticleForum Post: RE: SK-S7G2 QSPI BSP Support
Creating new BSP for SK by adding QSPI support from DK won't solve the issue. DK initializes the module a bit differently than the SK (or else it would be present in the SSP without any changes) but...
View Article