Forum Post: RE: Serial port settings for debug?
Dear Sir DJ Delorie, Could you kindly explain me how you use UART in SPI communication? Do I need write any cross protocol in my code? Selecting slave or master SPI, what would be code...
View ArticleForum Post: RE: Serial port settings for debug?
You should start a new topic for new questions. I haven't used the 63N yet, but I have some sample SPI code for the 62N here: www.delorie.com/.../microsd.c however my sample doesn't use the SCI...
View ArticleForum Post: RE: Serial port settings for debug?
Dear Sir, Thank you very much. As you can see, now for the particular device many additional include files are using depending on the IDE environment. I am uaing HEW and IAR. Did you run this code in...
View ArticleForum Post: RE: SH726A
Hi All, I am using SH726A controller. Need help to 1) enable program cache to speed up the processing time. 2)configure flash forfast processing. Thanks, Basanth S
View ArticleForum Post: SH726A
Hi All, I am using SH726A controller. Need help to 1) enable program cache to speed up the processing time. 2)configure flash forfast processing. Thanks, Basanth S
View ArticleForum Post: RE: GR_Kaede programming error
Sorry for the late reply. Did you try reprogramming the firmware ? Please see the page. renesasrulz.com/.../5618.aspx If you can not reprogram firmware, the GR-KAEDE board may have some trouble.
View ArticleForum Post: RE: GR_Kaede programming error
we have doubt about endian mode to select during flash programming- little or big endian
View ArticleForum Post: RE: GR_Kaede programming error
renesasrulz.com/.../added-file-image.jpg Sorry that the picture has only Japanese. This picture says the endian is set "Little" in "Basic Settings" area.
View ArticleForum Post: RE: GR_Kaede programming error
Please check if we are done with flashing firmware. Led 1-4 is flashing
View ArticleForum Post: RE: GR_Kaede programming error
I think it's OK and you can program your FW. Sorry that my first comments may not be correct... The error says "too large file". If the error exactly caused by the file size, an extra new KAEDE board...
View ArticleForum Post: RE: GR_Kaede programming error
I used simple led blink program to limit code size, but still getting error during sketch file upload.
View ArticleForum Post: RE: GR_Kaede programming error
Thank you for checking it. I think you may not spend so long time for this debugging, however could you try this way? First, use RFP to erase all area of micro controller and then program the firmware...
View ArticleForum Post: RE: GR_Kaede programming error
Yes, please take the mark of EB9 off. I think the erase process can finish because only EB8 and EB9 can be set the protect function.
View ArticleForum Post: RE: GR_Kaede programming error
Could you try to burn your program with another PC? When you success to write firmware that Fujimoto-san said, I want to confirm that. I don't understand your error, and never seen. 208k program is...
View ArticleForum Post: RE: GR_Kaede programming error
The board is working fine now!! Thanks a lot - Fujimoto Masashi and Okamiya Yuuki!!
View ArticleForum Post: RE: GR_Kaede programming error
The board is working fine now!! Thanks a lot - Fujimoto Masashi and Okamiya Yuuki!!
View ArticleForum Post: Error while linking "Error[e88]: Library tag ?CLRL78_V1_0_L00 not...
I am getting following error while linking : "Error[e88]: Library tag ?CLRL78_V1_0_L00 not found. Likely causes are compiler version mismatch, memory model mismatch or no library linked." I have...
View ArticleForum Post: RE: GR_Kaede programming error
Sounds good!! Thank you for trying without giving up. I wish you could have your best demonstration tomorrow.
View ArticleForum Post: RE: GR - Kaede Issues
So sorry for our late reply. Could you try the way I comments here. renesasrulz.com/.../5953.aspx
View Article