Forum Post: RE: SSP installed....
The SSP installer itself acts as a guide on how to install SSP. Carefully read the instructions on the various screens of the installer. The important part is to point the SSP installer to the base...
View ArticleForum Post: SSP Install...
Axel - thanks - I did all that. Matt - good to see you at Devcon - No, I dont get a Synergy Project when I try New project creation. Â That is my first and only clue. Â It seems easy but I just dont see...
View ArticleForum Post: RE: SSP Install...
Mark, You reply by using the box right below the previous entry on a thread; then click the Reply button below that box on the right hand side. Make sure to install e2 studio v4.1.0.017 from the...
View ArticleForum Post: Does anyone have a FreeRTOS demo that uses the LCD on the RSK +...
I've successfully compiled and run FreeRTOS, VDC, and DVD demos on the RSK + RZA1 board - but each one seems to have been written in very different ways. I'm wondering if anybody has successfully...
View ArticleForum Post: RE: SSP Install...
Mark, If you have to try uninstalling everything and reinstalling it. Â If you do the check for updates dont do the updates. Â Its a trap. Â Well hopefully it will work ok next time I do them, but I ran...
View ArticleForum Post: RE: SK-S7G2 schematics ?
Indeed Matt, as I said: I can't seem to find a FULL set of schematics, the user manual shows snippets. This is sort of indicated by the name of the manual:Â Renesas Synergy Starter Kit SK-S7G2 Data...
View ArticleForum Post: RE: RX23T - Excep_BRK when enabling FIR.FIEN
Hi all, bug is fixed. Command "fint" was missing in the corresponding #pragma interrupt definition.
View ArticleForum Post: RTC issues with GR-Kaede
I am facing below issues with RTC time stamp, please suggest.... I am reading RTC time and date every second and printing to serial terminal. Issue1 : "Second" is not getting rolled back to 0 after...
View ArticleForum Post: Preliminary Application Note EASE-AN-4050
Hello, Maybe possible help find "Preliminary Application Note EASE-AN-4050" ? Thank you in advance
View ArticleForum Post: SD Card Access?
Hello, I have successfully connected Kaede to PC and could able to see the Serial messages. Later, I have tried to capture images and put it into the SD card. I was successful initially while...
View ArticleForum Post: RE: SD Card Access?
The sequence of hard reset of Kaede was the issue. Up on following the proper sequence I could able to write data into SD card. Thanks. - Abid
View ArticleForum Post: RE: SK-S7G2 schematics ?
A complete schematic will be available on the gallery this Monday.
View ArticleForum Post: how to use arduino ide for a gr kaede board ?give one simple...
how to use arduino ide for a gr kaede board ?give one simple example code
View ArticleForum Post: RE: RTC issues with GR-Kaede
I tried your code after remove "Timer.h" that doesn't included in Web compiler. As a result, I couldn't repeat your problem. What development environment did you use? 23/10/15 18:36:0 23/10/15 18:36:1...
View ArticleForum Post: RE: how to use arduino ide for a gr kaede board ?give one simple...
I'm developing ide like arduino as below. Basically it's done, i'm preparing example code into that. Please wait for a little.
View ArticleForum Post: Issue creating a new Synergy project
I loaded E2 Studio version 4.1.0.017 and SSP 1.0.0-beta.1. When I attempt to create a new project referencing the lab procedure from lab 6L00IA - Introduction to Renesas Synergy Software Package...
View ArticleForum Post: RE: RTC issues with GR-Kaede
Thanks Okamiya Yuuki for your reply. I am using E2studio, i have also tried in web compiler but result is same as previous.
View ArticleForum Post: GR-Kaede EEPROM read write...!!
is anyone tried to write or read from Gr-Kaede EEPROM, i am facing some problem in that, please suggest.. I am writing single byte and reading back, code work fine just after dump, now if i disconnect...
View ArticleForum Post: RE: Where to find Registration ID?
sir, help me for above question to start doing Report work
View Article