Forum Post: RX210 RTC doesn't count in BCD code
I have found serious problem with RTC counters. I initialize RTC by RPDL function bellow. Seconds counter RSECCNT counts in hexadecimal format. As you can see on the print screen, the RSECCNT contains...
View ArticleForum Post: RE: R8C13 setup
A message about "R8C/1X" is not a typical E8a error message. In the simulator the device type is selected as R8C/1X or R8C/2X. Thus I think you try to start a simulator session. For a E8a session you...
View ArticleForum Post: RE: .MOT file CRC values
Hello Ravi (and all), Why can you not do for example this?
View ArticleForum Post: RE: Release notes, SSP 1.0.0: USBHS/USBFS controller support
Rich, There are 2 physical USB interfaces on SK board. The J5 is USB device micro B interface and J6 is USB host Type A interface. The J5 interface is connected to USBFS peripheral and configured...
View ArticleForum Post: RE: JPEG Working Example
Thank you very much! I'm going to test it tomorrow.
View ArticleForum Post: GUIX - Display View Rotation 90 degrees
I would like to rotate the display view of the S7G2 SK display +/-90 degrees? Is there any possibilty to do that in an easy way? And if yes, which points/issues must be taken in account? My poor...
View ArticleForum Post: RE: Single Console - Multiple Interfaces?
Ralph- I have created a short knowledge base article here with a project version of the Telnet console swap demo for the SK-S7G2 kit. Look it over and let me know if it works for you....
View ArticleForum Post: RE: e2studio V4.3.0.008 update failure
Try this: 1. In “eclipse\plugins\com.renesas.cg_n.n.n.nnnnnnnn\CodeGenerator\Tools\” (replacing n.n.n.nnnnnnnn with a version number under the e2 studio install director - Run “Unregister COM.bat” -...
View ArticleForum Post: RE: e2studio V4.3.0.008 update failure
Today Renesas released the offline installer for V.4.3.0.008. And there is also a new version 5.0.0.043 available. www.renesas.com/.../downloads.jsp
View ArticleForum Post: Programming R5F1026AA with MODE / TOOL0 PIN
Hello I am programming a RL78 device through the MODE pin. I enter programming mode and can access silicon signature, blank check etc. I send the PROGRAM COMMAND to program a 1K block of program area...
View ArticleForum Post: RE: JPEG Working Example
YES!!! Jeremy, the issue with the small images is solved. No need to upgrade e2studio, I'm using e2studio 4.2.0.012. Thanks! Note that copying the new file to the SRC folder has forced me to change...
View ArticleForum Post: RE: .MOT file CRC values
May be because you show the settings dialog for CC-RX, and the discussion is about GNURX? This is a GNURX dialog (admittedly not from V.16.01 but from V.15.02)
View ArticleForum Post: RE: Programming R5F1026AA with MODE / TOOL0 PIN
Thanks to anyone wanting to respond - ERROR found - all working - buffer was being over run in an interrupt routine - nothing to do with protocol.
View ArticleForum Post: RE: GUIX - Display View Rotation 90 degrees
Hello Ralph, The upcoming release of the SSP (1.1.0) implements screen rotation on a Framework level. Please look forward to finding it on the Gallery in the near future. The preview version (alpha)...
View ArticleForum Post: RE: e2studio V4.3.0.008 update failure
I have not tried Calvin's solution, I just uninstalled e2studio, en than re-installed V.4.3.0.007 and worked with that. This morning I installed V5, using the upgrade option in the offline installer....
View ArticleForum Post: RX63T has capability to measure RMS voltage?
Controller : RX63T Currently, we have a requirement to measure voltage from a source. Does this micro-controller have inbuilt capability to calculate the RMS value and store it in a register. The...
View ArticleForum Post: RE: R8C13 setup
I have successfully downloaded the v.1.05.01 full version and everything is back to normal Many thanks for your usual cooperation and expertise
View ArticleForum Post: RE: .MOT file CRC values
I think, the OP wants to implement his own code to validate the CRC. Ravi, Did you try this - 1. project name .map 2. search for these: .rvectors 0xfff#### .fvectors 0xfff#### And...
View ArticleForum Post: Debug code with SH7785 problem swich off Watchdog.
Hello everybody, i hope i post in the rigt section. i Debug code with a SH7785 mcu the problem is i cant swich off the Watchdog . i download the hardware manual and this is wat i did: WDTCSR: stop...
View ArticleForum Post: Timer Array Unit help
I am using the Timer Array Unit to coordinate a series of pulses through a speaker. Channel 1 is used as the square wave generator and Channels 0, 2 & 3 define different periods of either speaker...
View Article